Combo Set RAY G3 C3548-800 + RAY G2 60A controller # 3EA0168C
Combo set of the brushless outrunner electric motor with speed controller 60 A SBEC for aircraft models.
Trainer 2600g, aerobatic model 2300g, 3D 1500g, KV800 rpm / V, power supply Lixx 3-5s, shaft 4.0 mm
The RAY G3 motors are powerful 14-pole brushless electric motors with an external rotor bell ("Outrunner"). They have excellent electrical properties, an elaborate construction and perfect production processing. They are a very good choice as drives for your relaxation and sports models with excellent performance and a low price. They are low-speed, high-torque motors that turn large-diameter propellers without a gearbox.
The engine assembly:
RAY G3 C3548-800 is designed for mounting on both sides. For front mounting behind the motor bulkhead, use four M3 screws that are 4-5 mm apart on the motor bulkhead. The holes for the fastening screws on the front panel are equally spaced from the circular line with a diameter of 25 and 19 mm and are 180 degrees apart. The motor bulkhead should be made of 5 mm plywood. We deliver the stern mounting set (mounting cross and propeller driver) together with the motor.RAY G3 C3548-800 is a brushless motor for models with an all-up weight of up to 2700 g, with power supply from a 4- to 5-cell Li-Po battery. This motor is suitable for models like our EPP "Warbirds" and Akro models with a wingspan of 1300-1400 mm, Spitfire EP or Mustang EP from Phoenix and the like.
Power supply LiXX cells: 3 - 5;
Revolutions per volt [rpm / volt]: 800; Max. Power (30 s / 5S LiPo) [W]: 660
No-load current (3S) [A]: 2.2; Max. Peak current (30 s) [A]: 48
Diameter [mm]: 35; Length [mm]: 48
Shaft diameter [mm]: 4
-------------------------------------------------- -------------------------------------------------- -------------------------------------------------- -------------------------------------------------- -------------------------------------
Programmable microprocessor controller of the new generation (G2) for brushless sensorless motors, which was constructed with the help of modern semiconductor technology. Compared to the first generation, it offers easier and clearer programming with the transmitter and really simple and lightning-fast setting using the new LED programming card RAY G2 (sold separately). It is used to control the speed of the brushless electric motors in leisure aircraft models with power supply from NiCd / NiMH and LiPo / Li-ion batteries. It is equipped with the linear BEC system, which secures the power supply of the receiver and the servos from the drive battery.
DESCRIPTION AND FUNCTIONS OF THE CONTROLLER
Extremely low internal resistance thanks to the new generation of powerful MOSFET transistors
Suitable for most brushless aircraft motors with power supply from 2-6S LiPo / Li-ion or 5-18 cell NiCd / NiMH batteries
For power supply from the rechargeable batteries NiCd, NiMH, LiPo, Li-ion
Linear stabilizer BEC 6.0 V can be loaded with up to 5 A.
Adjustable timing for optimal adaptation to the engine
Adjustable undervoltage protection - the motor switches off in the event of undervoltage
Safe switch-on (prevents the motor from starting when switched on)
Temperature overload protection against overload (when the temperature reaches 110 degrees, the controller reduces the output)
Automatic engine shutdown if the transmitter signal is lost
Linear regulation of the gas
Simple programming and setting using the transmitter or the RAY G2 LED programming card
Calibration of the throttle path for perfect adaptation to the transmitter signal of your RC set
PROGRAMMABLE FUNCTIONS
Brake (off - on)
Selectable battery type (Li-poly or NiCd / NiMH)
Type of motor cut-out: Reduce the motor output or switch off the motor
Adjustable undervoltage for switching off the engine - undervoltage protection against excessive discharge of the batteries. (Lithium batteries: 2.85 V / cell, 3.15 V / cell, 3.3 V / cell; NiXX battery: 0% / 50% / 65% from the initial value of the voltage)
Resetting the controller to factory settings
Adjustable timing - for increasing the effectiveness and optimal adaptation of the motor - low (3.75 degrees), medium (15 degrees), high (26.25 degrees)
Adjustable soft start for motors with gearbox and helicopter in three stages: normal (300 ms) / soft (1.5 s) / super soft (3 s)
PROTECTIVE FUNCTIONS OF THE REGULATOR
Protection during start-up: If the motor does not start within 2 seconds after accelerating, the controller switches the motor off.
Thermal protection: If the temperature of the controller exceeds 110 degrees, the controller will limit the output power.
Loss of the gas signal: the controller limits the power if the signal is absent for 1 second; If the signal is missing for more than 2 seconds, the engine is switched off.
Tip: When switching on the controller for the first time, perform the calibration first the gas path according to the instructions. Only then is it possible to use the controller and set other parameters with the aid of the transmitter or the RAY G2 LED programming card.
Usage: airplane, helicopter
Type: Brushless; Continuous current [A]: 60
Max. Peak current [A]: 80; NiXX cells: 5 - 18
LiXX cells: 2 - 6
BEC voltage [V]: 6
BEC current [A]: 5
Length [mm]: 77; Width [mm]: 35; Height [mm]: 14
Weight [g]: 63
.JPG "Combo Set RAY G3 C3548-800 + RAY G2 60A controller # 3EA0168C")
.JPG "Combo Set RAY G3 C3548-800 + RAY G2 60A controller # 3EA0168C")
